111-27DIELECTRIC COATING介質涂層

描述：111-27是一種柔性、電絕緣涂層，適用于噴涂、浸漬和應用。

注射器分配。本產品具有與卡普頓、聚酯薄膜、玻璃等多種材料良好的附著力。

表面。與傳統的絕緣材料不同，該產品非?？箯澢驼郯?。一些

111-27的應用包括但不限于絕緣聚酰亞胺柔性電路、聚合物厚膜。

電路和薄膜開關。111-27還可防止部件受潮、鹽分和磨損。

典型固化特性：

稠稠液體

抗皺性佳

水汽透過率低

抗真菌非營養

符合MIL-I-46058C的電氣性能

絕緣電阻，歐姆（1至3密耳薄膜）：

循環1 25°C/50%R.H.1x1015

循環4 65°C/95%r.h.4x1010

循環7 65°C/95%相對濕度5x1010

循環10 65°C/95%r.h.2x1010

循環10后24小時25°C/50%相對濕度2x1013

泄漏率：

熱沖擊前，微安<10

熱沖擊后，微安<10

1500伏，50赫茲時的介電耐受：

在熱沖擊和潮濕暴露通過之前

經過熱沖擊和潮濕暴露后

體積電阻率（歐姆厘米）1.1 x 1014

介電強度（伏特/密耳）1300

損耗因數（100赫茲）0.011

介電常數（100赫茲）4.1

建議的處理和固化：可通過以下方法進一步稀釋噴涂和/或浸涂

正在添加mek。在130°C下固化3分鐘后，大多數應用的性能佳。良好

通過在25°C至150°C的溫度范圍內固化，可在多種基材上獲得性能。終用戶

建議通過實驗確定適合個人應用的溫度和時間。

貯存期：21°C下保存6個月。

安全和操作：在通風良好的情況下使用。遠離火花和明火。避免長時間

接觸皮膚和吸入蒸汽。用肥皂和水清洗皮膚。保持容器關閉

避免污染；濕氣可能引起聚合。用惰性氣體毯吹掃打開的容器

重新密封之前。

111-27DIELECTRIC COATING介質涂層

111-27
 DIELECTRIC COATING
DESCRIPTION: 111-27 is a flexible, electrically insulating coating suitable for application by spraying, dipping and
syringe dispensing. This product features excellent adhesion to Kapton, Mylar, glass, and a variety of other
surfaces. Unlike conventional insulating materials, this product is very resistant to flexing and creasing. Some
applications for 111-27 include, but are not limited to, insulating polyimide flexible circuits, polymer thick film
circuitry, and membrane switches. 111-27 also protects components from moisture, salts, and abrasion.
TYPICAL CURED PROPERTIES:
 Consistency Thick liquid
Crease resistance Excellent
Moisture vapor transmission Low
Fungus resistance Non-nutrient
Electrical Properties Per MIL-I-46058C
Insulation resistance, ohms (1 to 3 mil film):
Cycle 1 25°C/50% R.H. 1x1015
Cycle 4 65°C/95% R.H. 4x1010
Cycle 7 65°C/95% R.H. 5x1010
Cycle 10 65°C/95% R.H. 2x1010
24 hours after cycle 10 25°C/50% R.H. 2x1013
Leakage rate:
Before thermal shock, microamperes < 10
After thermal shock, microamperes < 10
Dielectric withstand at 1,500 volts, 50 Hz:
Before thermal shock and moisture exposure Pass
After thermal shock and moisture exposure Pass
 Volume Resistivity (ohm-cm) 1.1 x 1014
 Dielectric Strength (volts/ mil) 1300
Dissipation Factor (100 Hz) 0.011
Dielectric Constant (100 Hz) 4.1
SUGGESTED HANDLING & CURING: Further thinning for spray and/or dip coating may be accomplished by
adding MEK. Best properties for most applications result when allowed to be cured for 3 minutes at 130°C. Good
properties are obtained on a variety of substrates by curing at temperatures ranging from 25°C to 150°C. End user
is advised to experimentally determine temperature and time best suited for individual applications.
STORAGE: Shelf Life: 6 months at 21°C.
SAFETY & HANDLING: Use with adequate ventilation. Keep away from sparks and open flames. Avoid prolonged
contact with skin and breathing of vapors. Wash with soap and water to remove from skin. Keep containers closed
to avoid contamination; moisture may cause polymerization. Purge opened containers with an inert gas blanket
before resealing.